Logo Wöhler

01 bundle cutter

Precise cuts in all cases of application
+ precision cut tolerances +/- 0.02" (0.5 mm)
+ short bundle lengths
+ extremely long blade service time
BC 100
Precise cutting of natural hair bundles
+ up to 15 cuts/Minute
+ bundle diameter from 2.2" to 3.5" (55 - 90 mm )
+ bundle length from 2.75" to 7.9" (70 - 200 mm )
BC 200
Precise cuts in all cases of application
+ up to 35 cuts/min
+ precision cut tolerances +/- 0.02" (0.5 mm)
+ short bundle lengths
+ extremely long blade service time
BC 500
BC 500
Precise cuts in all cases of application
+ up to 30 cuts/min + precision cut tolerances +/- 0.02" (0.5 mm) + clean cut and scrap bundle sorting + extremely long blade service time
BC 700
BC 700
Precise cuts in all cases of application
+ up to 70 cuts/min
+ precision cut tolerances +/- 0.008“ (0.2 mm)
+ short bundle lengths
+ extremely long blade service time
+ natural filament cutting (optional)
+ automatic remaining length processing (optional)
+ fast manual operation for flexible materials (optional)
+ fully automatic bundle length sorting into two containers (optional)
BC 810
BC 810
BC 810

01 Gutter broom machines

Gutter broom production with perfect fitting and retaining
+ freely programmable hole pattern
+ automatic wire and poly filament feeding
+ stronger cleaning effect through optimized plate design
+ maximum bundling effect by adjusting the angle
+ large program memory
GB 20
GB 20
Consistent quality from the very beginning
+ high production speed
+ counted and tied flat wire bundles
+ wire pay-off from coil (Z2/Z3) load-free strippable
+ direct influence on product quality
+ wire thickness control unit FTC 250 (optional)
+ flat wire bundle knoter FBK 250 (optional)
+ coupleable with various assembly machines
FWR 250
FWR 250
FWR 250
Optimal combination with the flat wire rolling machine FWR 250
+ capacity: up to 787 ft/min (240 m/min)
+ electronic torque control
+ precision wire guiding
+ adjustable laying device for optimal winding results
Wire tuft brush production
+ fully automatic process
+ high process reliability
+ high production speed
+ simple coupling with existing FWR 250
FWB 700
FWB 700
FWB 700

01 Twist knot brush machines

Unique twist knot forms – extraordinary speed
+ punching integrated
+ disk changing under 1 second
+ enhanced output up to 130% (100% = ZVA 600)
+ up to 30 knots/min
+ outer brush diameter up to 12.5“ (320 mm)
+ integrated spining-station for perfect alignment and fewer steps before mounting
+ knot shape freely programmable in three sections
ZVA 320
ZVA 320
ZVA 320
High output twist knot brush machine
+ up to 200% output (100% = ZVA 600)
+ up to 60 knots/min
+ brush diameter up to 12.5" (320 mm)
+ automatic disk feeding
ZVA 322
ZVA 322
ZVA 322
Flexible in large and small series
+ high production capacity
+ ideal for operating in production cells
+ brush size from 6-hole disks up to 23.6" (600 mm) outer diameter
+ automatic disc feeding (optional)
+ integrated hole punching (optional)
ZVA 600
ZVA 600
ZVA 600
Individual small series production – fast and easy
+ highest flexibility
+ low investment costs
+ up to 6 knots/min
+ programmable twist knot styles
+ up to 200 brush programs
ZL 300

02 Brush segment machines

Produce economically from lot size 1
+ each segment size can be produced in any sequence with minimum setup effort
+ lowers your inventory
+ only one sheet instead of ring and eyelet
+ integrated disc punching
+ freely adjustable fill material length reduces wire consumption
+ optimally balanced segments through best wire distribution
+ up to 25% higher stocking density
+ securely fixed fill material
SHF 400
SHF 400
SHF 400
Powerbrush semgents with highest balancing
+ production capacity up to 12 segments/min
+ radial, non-grid fill alignment
+ high balancing
+ assembly-ready segments
+ wheel and cup brush assembly unit (optional)
BSM 110 + RS 100
BSM 110 + RS 100
BSM 110 + RS 100
Flexible production with lowest costs
+ high flexibility thanks to optimised product change-over system
+ large size range from 1.1" - 4.7" (28 - 120 mm) inner diameter
+ minimal wire loss
+ servo-driven wire feeding for reproducible settings
+ precise eyelet widths up to 5.9" (150 mm) inner diameter
+ 100% compatibility with BSM 83 tooling sets
+ modular upgrading to fully automatic production
BSM 200 + SPR 300 | SPR 410
BSM 200 + SPR 300 | SPR 410
BSM 200 + SPR 300 | SPR 410
Fully automatic brush segment production with inline brush trimming
+ high production capacity up to 11 segments/min + segment diamter up to 12.6" (320 mm) + perfect fill distribution with high density + high balancing quality + trimming unit with long service life + minimal wire consumption + maintenance-friendly servomotor technology + simple length change via recipe selection + reduced set-up times
BSM 330 + STM 200 | STM 300
BSM 330 + STM 200 | STM 300
BSM 330 + STM 200 | STM 300
„Hotani Style“ brush segment production and refill
+ automatic production of so-called Hotani disks
+ including hole punching
+ controlled bundle fixing with consistent force
+ clean cutting and bending of the binding wire
+ fast change-over for different disc sizes and bundle lengths
HSH 95
HSH 95
HSH 95
Hotany brush segment production using various common fill materials
+ semi- and full-automatic production of Hotany disks
+ picker for many common fill materials
+ controlled bundle fixing with consistent force
+ clean cutting and bending of the binding wire + fast change-over for economical small series production + upgradable to fully automatic, unattended operation (optional) + integrated punching station (optional)
HSH 100
HSH 100
HSH 100
Brush segments with extra high density
+ high variation – from normal to high density segments
+ perfect fill distribution – high balancing
+ minimum loss of material
+ manual or automatic fill material feeding
+ nominal diameters from 1.1" to 7.1" (28 - 180 mm)
+ outer segment diameter up to 15.75" (400 mm)
BSM 83 HD + SPR 300
BSM 83 HD + SPR 300
BSM 83 HD + SPR 300
Brush segments with extra high density and automatic wire feeding
+ high variation – from normal to high density segments
+ perfect fill distribution – high balancing
+ minimum loss of material
+ manual or automatic fill material feeding
+ nominal diameters from 1.1" to 7.1" (28 - 180 mm)
+ outer segment diameter up to 15.75" (400 mm)
+ automatic wire feeding
BSM 83 HD + TFD 290 + SPR 300
BSM 83 HD + TFD 290 + SPR 300
BSM 83 HD + TFD 290 + SPR 300

02 Cassette brush machines

Fully automatic cassette brush production
+ fully automatic process
+ wire bundle clip for perfect grip
+ incl. wire crimping from Z2-coil
+ no trimming required
+ endless retaining wire from coil
+ improved fixation of the retaining wire
+ production of wire mats (optional)
GB 90
GB 90

02 Wire crimping and cutting

Wire crimping and cutting with high speed
+ high process reliability and availability
+ improved straightness of wires
+ easy to use
+ minimal set-up times when changing over to a different product
+ wide range of the processed wires
+ nearly compatible with any type of coil
DA 400 | DA 700
DA 400 | DA 700
Precise workmanship even with fine wires
+ speed up to 19.7 ft/s (6 m/s)
+ adjustable number of wires per hank
+ CNC ground crimping gears
+ finest wires processed without any damage
USTW 6000
Precise workmanship even with fine wires
+ CNC ground crimping gears, no nesting
+ finest wires processed without any damage
+ rapid change units and precise displays
+ wire straightening facility with fine gears
STW 87 – STW 96
Wire cutting with high speed
+ high production capacity
+ cut lengths 3.9" - 12.8" (100 - 325 mm)
+ integrated straightening, crimping and bundling possible
SWC 950

03 Brush segments

Gutter broom production with perfect fitting and retaining
+ wire, synthetics and mixed fill
+ great product diversity
+ homogeneous fill
+ quick assembly tool set-up
ERS 69
Brush segment production from classic to individual
+ wire, synthetics and mixed fill
+ integrated wire crimping and cutting
+ great product diversity
+ homogeneous fill
+ quick assembly tool set-up
ERS 990
Metal ring production for the brush industry
+ diameter from 3“ to 13.5“ (75 to 350 mm)
+ U- and V-profiles
+ 1 or 2 hole punching
RWA 980
RWA 980

03 End brush machines

Fully automatic production of end brushes
+ high production capacity
+ semi to fully automatic production possible
+ for all fill materials from hank
+ with and without support elements
+ labeling of shafts optionally possible
EBM 88
EBM 88

03 Roller cutter

Cutting hanks of wire manually
+ HSS or carbide cutting blades
+ various different models and fittings
Easy and precise trimming of power brush segments
+ carbide roller cutting blades
+ sturdy construction
+ large range of productse

04 Brush bodies

Economic production of thick-walled brush body tubes
+ production rate of up to 220 lbs/hour
+ production of thickwalled tubes for stable-set brushes
+ low-cost raw-materials (regranulate HDPE, PP)
PPR 150
PPR 150
Economic production of thick-walled tube brush and gutter broom bodies
+ tubes of up to 0.7“ (18 mm) wall thickness
+ especially for parts with large wall thickness like for staple set brushes
+ up to 8 tool stations, modularly expandable
+ use of low-cost materials (regranulat, HDPE, PP)
+ low investment costs for tool sets
+ tubes with inner/outer profiles (drivers)
BBM 700
BBM 700
BBM 700

04 Bundling crimping cutting machines

Precise cuts in all cases of application
+ precision cut tolerances +/- 0.02" (0.5 mm)
+ short bundle lengths
+ extremely long blade service time
BC 100
Precise cutting of natural hair bundles
+ up to 15 cuts/Minute
+ bundle diameter from 2.2" to 3.5" (55 - 90 mm )
+ bundle length from 2.75" to 7.9" (70 - 200 mm )
BC 200
Precise cuts in all cases of application
+ up to 35 cuts/min
+ precision cut tolerances +/- 0.02" (0.5 mm)
+ short bundle lengths
+ extremely long blade service time
BC 500
BC 500
Precise cuts in all cases of application
+ up to 30 cuts/min + precision cut tolerances +/- 0.02" (0.5 mm) + clean cut and scrap bundle sorting + extremely long blade service time
BC 700
BC 700
Precise cuts in all cases of application
+ up to 70 cuts/min
+ precision cut tolerances +/- 0.008“ (0.2 mm)
+ short bundle lengths
+ extremely long blade service time
+ natural filament cutting (optional)
+ automatic remaining length processing (optional)
+ fast manual operation for flexible materials (optional)
+ fully automatic bundle length sorting into two containers (optional)
BC 810
BC 810
BC 810
Wire crimping and cutting with high speed
+ high process reliability and availability
+ improved straightness of wires
+ easy to use
+ minimal set-up times when changing over to a different product
+ wide range of the processed wires
+ nearly compatible with any type of coil
DA 400 | DA 700
DA 400 | DA 700
Precise workmanship even with fine wires
+ speed up to 19.7 ft/s (6 m/s)
+ adjustable number of wires per hank
+ CNC ground crimping gears
+ finest wires processed without any damage
USTW 6000
Precise workmanship even with fine wires
+ CNC ground crimping gears, no nesting
+ finest wires processed without any damage
+ rapid change units and precise displays
+ wire straightening facility with fine gears
STW 87 – STW 96
Sandpaper cutting in arbitrary contours and outlines
+ laser cutting of grinding paper
+ specially adjusted to common band dimensions
+ easy programming
+ arbitrary contours and outlines
L 200 WSC – L 400 WSC
L 200 WSC – L 400 WSC
L 200 WSC – L 400 WSC
Cutting hanks of wire manually
+ HSS or carbide cutting blades
+ various different models and fittings

04 trimming, assembly, equipment

Cutting hanks of wire manually
+ HSS or carbide cutting blades
+ various different models and fittings
Wire cutting with high speed
+ high production capacity
+ cut lengths 3.9" - 12.8" (100 - 325 mm)
+ integrated straightening, crimping and bundling possible
SWC 950
Individual and flexible coil excitation for a brush to-measure production
+ optimised inventory
+ individual fill material mix
STS 460
Easy and precise trimming of power brush segments
+ carbide roller cutting blades
+ sturdy construction
+ large range of productse
Compact and versatile – ideal for flexible small lots
+ fast product change, short changeover
+ rapid clamping system for high production capacity
+ good accessibility
+ easy to clean
+ top mounted guide and trimmer
Compact and versatile – ideal for high performance
+ fast product change, short changeover
+ rapid clamping system for high production capacity
+ good accessibility
+ easy to clean
+ top mounted guide and trimmer
Fully automatic working cycle for minimal start-up times at product changing
+ fast product change
+ rapid brush changing in the production cycle
+ start-up programm for diameter control
+ automatic pre-positioning and clearing
+ brush holder for rollers and segments
+ easy cleaning
+ 5 work cycles in sequence
TU 500
TU 500
TU 500
Innovative machine design – any contours
+ up to 39.4" (1000 mm) diameter
+ trim length up to 8.2 ft (2.5 m) or up to 16.4 ft (5.0 m)
+ CNC contour trimming
+ simple upload of G-Code-programs
+ fast trimmer change
+ quick clamping system for efficient brush loading
MTB 1000
MTB 1000

05 crimping, cutting, bundling

Wire crimping and cutting with high speed
+ high process reliability and availability
+ improved straightness of wires
+ easy to use
+ minimal set-up times when changing over to a different product
+ wide range of the processed wires
+ nearly compatible with any type of coil
DA 400 | DA 700
DA 400 | DA 700
Cutting hanks of wire manually
+ HSS or carbide cutting blades
+ various different models and fittings
Loss-free production, cutting and bundling of synthetic filaments
+ materials from 0.04“ to 0.08“ x 0.16“ diameter
+ material length from 4.9" to 27.6" (125 - 700 mm)
+ loss-free production without waste
+ direct bundling with foil wrapping
+ particularly straight filaments
+ high cutting capacity
PCD 1100

05 Laser cutting machines

Sandpaper cutting in arbitrary contours and outlines
+ laser cutting of grinding paper
+ specially adjusted to common band dimensions
+ easy programming
+ arbitrary contours and outlines
L 200 WSC – L 400 WSC
L 200 WSC – L 400 WSC
L 200 WSC – L 400 WSC

Automotive industry

Removes overspray and contamination with consistent surface quality
+ optimal cleaning
+ without affecting the surface finish
+ consistent surface quality finish through special brushes
+ individually programmable production parameters
+ continuous quality control by camera recognition of disc geometry and hole patterns
+ automatic rejection of scrap discs
+ labelling with part or batch number data
B 94
B 94
B 94

Brush application

Removes overspray and contamination with consistent surface quality
+ optimal cleaning
+ without affecting the surface finish
+ consistent surface quality finish through special brushes
+ individually programmable production parameters
+ continuous quality control by camera recognition of disc geometry and hole patterns
+ automatic rejection of scrap discs
+ labelling with part or batch number data
B 94
B 94
B 94
Processing of all profile sides in a single run
+ individual configuration
+ Stand alone or integrated in systems
+ 3D surface processing
+ closed operating cell with extraction
+ highest safety for people and materials
B 63
B 63
B 63
Endless natural wood grain effect and individual patterns
+ realistic and natural 3D effect
+ great selection of patterns and structures
+ suitable for all profile types
+ single and double sided processing
+ fast and simple tooling
E12-14
E12-14
E12-14

Brush trimming machines

Compact and versatile – ideal for flexible small lots
+ fast product change, short changeover
+ rapid clamping system for high production capacity
+ good accessibility
+ easy to clean
+ top mounted guide and trimmer
Compact and versatile – ideal for high performance
+ fast product change, short changeover
+ rapid clamping system for high production capacity
+ good accessibility
+ easy to clean
+ top mounted guide and trimmer
Fully automatic working cycle for minimal start-up times at product changing
+ fast product change
+ rapid brush changing in the production cycle
+ start-up programm for diameter control
+ automatic pre-positioning and clearing
+ brush holder for rollers and segments
+ easy cleaning
+ 5 work cycles in sequence
TU 500
TU 500
TU 500
Cost-efficient trimming of staple set and wound roll and disc brushes
+ brush diameter up to 3.3 ft (1 m)
+ brush weight up to 3.300 lbs (1.5 t)
+ standard lengths up to 6.6 ft (2.0 m) (optionally up to 19.0 ft (5.8 m))
+ proven FS 930 trimming technology
+ contour trimming (optional)
+ disc brush trimming (optional)
+ chip extraction and cleaning-friendly design
Innovative machine design – any contours
+ up to 39.4" (1000 mm) diameter
+ trim length up to 8.2 ft (2.5 m) or up to 16.4 ft (5.0 m)
+ CNC contour trimming
+ simple upload of G-Code-programs
+ fast trimmer change
+ quick clamping system for efficient brush loading
MTB 1000
MTB 1000
Universal application optimised blade geometry
+ universal trimming
+ automatic blade lubrication
+ flexible adjustment for cutting all kinds of brushes
+ installation on a trimming bench possible
ZS 90 + UF 900
Trimming of cup, wheel and end brushes with and without shank
+ high capacity
+ cup and wheel brushes
+ natural, synthetic, wire fill
+ with and without shank
FVD 92 | FVD 940

Bundle cutter

Precise cuts in all cases of application
+ precision cut tolerances +/- 0.02" (0.5 mm)
+ short bundle lengths
+ extremely long blade service time
BC 100
Precise cuts in all cases of application
+ up to 35 cuts/min
+ precision cut tolerances +/- 0.02" (0.5 mm)
+ short bundle lengths
+ extremely long blade service time
BC 500
BC 500
Precise cuts in all cases of application
+ up to 30 cuts/min + precision cut tolerances +/- 0.02" (0.5 mm) + clean cut and scrap bundle sorting + extremely long blade service time
BC 700
BC 700
Precise cuts in all cases of application
+ up to 70 cuts/min
+ precision cut tolerances +/- 0.008“ (0.2 mm)
+ short bundle lengths
+ extremely long blade service time
+ natural filament cutting (optional)
+ automatic remaining length processing (optional)
+ fast manual operation for flexible materials (optional)
+ fully automatic bundle length sorting into two containers (optional)
BC 810
BC 810
BC 810

Dental and Polishing Brush Machines

Trimming of cup, wheel and end brushes with and without shank
+ high capacity
+ cup and wheel brushes
+ natural, synthetic, wire fill
+ with and without shank
FVD 92 | FVD 940
Fully automated production - enormous product variety
+ high production capacity
+ Junior Cup, Dremel, cup and wheel brushes
+ optimised fill feeding systems
+ with and without shank
+ integrated trimming
DBM 90
DBM 90
DBM 90
Individual production with great variety of products
+ high flexibility
+ modular design
+ universal production of all brush types
+ special brush design
+ suitable for productions of very small lots
DBV 90
DBV 90
Individual production with great variety of products
+ high flexibility
+ modular design
+ from manual to fully automatic
+ use of pre-formed bundles
EDS 91

Finishing stations

Final processing of strip brushes with long, soft filaments
+ for all fill lengths from short to very long, soft fill material
+ process reliability and high quality
+ easy product range expansion
+ also supplements existing machines
+ easy integration in existing production lines
+ also for stand-alone operation
+ user and set-up friendly
FSA 500
FSA 500

HiT High temperature brushes

Innovative, high performance, high flexible
+ considerably higher efficiency compared to conventional processes
+ durability – abrasion resistance – long service life
+ high working temperatures possible
+ cut in production costs through reduced process times
+ no additives required
+ fast and extensive processing, gentle to surfaces
+ defined edge rounding
+ for use on standard machines or integrated in production lines
HiT-Brush-Technology
HiT-Brush-Technology
HiT-Brush-Technology
Variable, modular and powerful
+ digital displayed pressure control and variable speed
+ modular and stable design
+ easy adaption to existing lathes and polishing benches
+ specially designed for processing of roll bodies
+ automatic balancing of radial run out in the rolls
SA 100 B
SA 100 B
SA 100 B

milling cutter, roller cutter, clipper trimmer

Universal application optimised blade geometry
+ universal trimming
+ automatic blade lubrication
+ flexible adjustment for cutting all kinds of brushes
+ installation on a trimming bench possible
ZS 90 + UF 900

Powerbrush machines

Cutting hanks of wire manually
+ HSS or carbide cutting blades
+ various different models and fittings
Wire cutting with high speed
+ high production capacity
+ cut lengths 3.9" - 12.8" (100 - 325 mm)
+ integrated straightening, crimping and bundling possible
SWC 950
Unique twist knot forms – extraordinary speed
+ punching integrated
+ disk changing under 1 second
+ enhanced output up to 130% (100% = ZVA 600)
+ up to 30 knots/min
+ outer brush diameter up to 12.5“ (320 mm)
+ integrated spining-station for perfect alignment and fewer steps before mounting
+ knot shape freely programmable in three sections
ZVA 320
ZVA 320
ZVA 320
High output twist knot brush machine
+ up to 200% output (100% = ZVA 600)
+ up to 60 knots/min
+ brush diameter up to 12.5" (320 mm)
+ automatic disk feeding
ZVA 322
ZVA 322
ZVA 322
Flexible in large and small series
+ high production capacity
+ ideal for operating in production cells
+ brush size from 6-hole disks up to 23.6" (600 mm) outer diameter
+ automatic disc feeding (optional)
+ integrated hole punching (optional)
ZVA 600
ZVA 600
ZVA 600
Individual small series production – fast and easy
+ highest flexibility
+ low investment costs
+ up to 6 knots/min
+ programmable twist knot styles
+ up to 200 brush programs
ZL 300
Produce economically from lot size 1
+ each segment size can be produced in any sequence with minimum setup effort
+ lowers your inventory
+ only one sheet instead of ring and eyelet
+ integrated disc punching
+ freely adjustable fill material length reduces wire consumption
+ optimally balanced segments through best wire distribution
+ up to 25% higher stocking density
+ securely fixed fill material
SHF 400
SHF 400
SHF 400
Powerbrush semgents with highest balancing
+ production capacity up to 12 segments/min
+ radial, non-grid fill alignment
+ high balancing
+ assembly-ready segments
+ wheel and cup brush assembly unit (optional)
BSM 110 + RS 100
BSM 110 + RS 100
BSM 110 + RS 100
Flexible production with lowest costs
+ high flexibility thanks to optimised product change-over system
+ large size range from 1.1" - 4.7" (28 - 120 mm) inner diameter
+ minimal wire loss
+ servo-driven wire feeding for reproducible settings
+ precise eyelet widths up to 5.9" (150 mm) inner diameter
+ 100% compatibility with BSM 83 tooling sets
+ modular upgrading to fully automatic production
BSM 200 + SPR 300 | SPR 410
BSM 200 + SPR 300 | SPR 410
BSM 200 + SPR 300 | SPR 410
Fully automatic brush segment production with inline brush trimming
+ high production capacity up to 11 segments/min + segment diamter up to 12.6" (320 mm) + perfect fill distribution with high density + high balancing quality + trimming unit with long service life + minimal wire consumption + maintenance-friendly servomotor technology + simple length change via recipe selection + reduced set-up times
BSM 330 + STM 200 | STM 300
BSM 330 + STM 200 | STM 300
BSM 330 + STM 200 | STM 300

Street Sweeper Brush Machines

Wire crimping and cutting with high speed
+ high process reliability and availability
+ improved straightness of wires
+ easy to use
+ minimal set-up times when changing over to a different product
+ wide range of the processed wires
+ nearly compatible with any type of coil
DA 400 | DA 700
DA 400 | DA 700
Cutting hanks of wire manually
+ HSS or carbide cutting blades
+ various different models and fittings
Gutter broom production with perfect fitting and retaining
+ freely programmable hole pattern
+ automatic wire and poly filament feeding
+ stronger cleaning effect through optimized plate design
+ maximum bundling effect by adjusting the angle
+ large program memory
GB 20
GB 20
Consistent quality from the very beginning
+ high production speed
+ counted and tied flat wire bundles
+ wire pay-off from coil (Z2/Z3) load-free strippable
+ direct influence on product quality
+ wire thickness control unit FTC 250 (optional)
+ flat wire bundle knoter FBK 250 (optional)
+ coupleable with various assembly machines
FWR 250
FWR 250
FWR 250
Optimal combination with the flat wire rolling machine FWR 250
+ capacity: up to 787 ft/min (240 m/min)
+ electronic torque control
+ precision wire guiding
+ adjustable laying device for optimal winding results
Wire tuft brush production
+ fully automatic process
+ high process reliability
+ high production speed
+ simple coupling with existing FWR 250
FWB 700
FWB 700
FWB 700
Fully automatic cassette brush production
+ fully automatic process
+ wire bundle clip for perfect grip
+ incl. wire crimping from Z2-coil
+ no trimming required
+ endless retaining wire from coil
+ improved fixation of the retaining wire
+ production of wire mats (optional)
GB 90
GB 90
Economic production of thick-walled brush body tubes
+ production rate of up to 220 lbs/hour
+ production of thickwalled tubes for stable-set brushes
+ low-cost raw-materials (regranulate HDPE, PP)
PPR 150
PPR 150
Economic production of thick-walled tube brush and gutter broom bodies
+ tubes of up to 0.7“ (18 mm) wall thickness
+ especially for parts with large wall thickness like for staple set brushes
+ up to 8 tool stations, modularly expandable
+ use of low-cost materials (regranulat, HDPE, PP)
+ low investment costs for tool sets
+ tubes with inner/outer profiles (drivers)
BBM 700
BBM 700
BBM 700
Gutter broom production with perfect fitting and retaining
+ wire, synthetics and mixed fill
+ great product diversity
+ homogeneous fill
+ quick assembly tool set-up
ERS 69

Strip brush machines

Strip brush production with up to 130.0 ft/min
+ high speed production with up to 130.0 ft (40.0 m/min)
+ modularly upgradable for new products
+ U and Y profiles
+ profile sizes from 0.06" to 0.32" (1.5 - 8.0 mm)
+ product change – quick and easy
+ visualised fill density and height control for high process reliability
SBM 92
SBM 92
SBM 92
Simple, tough and profitable
+ high flexibility – fast product change
+ new products – quick and fast set-up
+ fill material picker for natural, synthetic, abrasive and wire
+ sufficient space for hand feeding
+ profile sizes from 0.06" (1.5 mm) to 0.24" (6.0 mm)
+ production speed up to 16.4 ft/min (5.0 m/min)
SBM Basic
Strip brush production in unbeatable quality at unrivalled speed
+ up to 39.5 ft/min (12.0 m/min) (optional up to 130.0 ft/min (40.0 m/min))
+ fill material length up to 27.6" (700.0 mm)
+ profile width from 0.12" to 0.5" (3.0 mm - 13.0 mm) (up to 0.8" (20.0 mm) on SBM 840 XL)
+ U- and Y-profiles
SBM 840
SBM 840
High fill density and optimal fixing in strips and brush packages
+ quality roller brushes for heavy duty
+ high density
+ automatic production of brush packages
+ strong and save fixation of the filaments
SPI 90
Flexible strip brushes for applications with high demands on cleanness and hygiene
+ corrosion free applications
+ ultra light, full plastic strip and roll brushes
+ high density and closed fill
+ economic endless production or cut to length
MSB 960
MSB 960
MSB 960
Roll brushes with up to 8 m length direct in line with strip brush production
+ direct winding in line with your strip brush machine
+ high production speed even at small diameters
Winding and cutting of roll brushes out of endles strip brush
+ special design for easy integration in line with a strip brush machine
+ automatic speed compensation between winding and strip brush machine
+ automatic cutting according to individual number of turns without production stop
WAC 800
Precise cuts in all cases of application
+ precision cut tolerances +/- 0.02" (0.5 mm)
+ short bundle lengths
+ extremely long blade service time
BC 100
Precise cuts in all cases of application
+ up to 35 cuts/min
+ precision cut tolerances +/- 0.02" (0.5 mm)
+ short bundle lengths
+ extremely long blade service time
BC 500
BC 500
Precise cuts in all cases of application
+ up to 30 cuts/min + precision cut tolerances +/- 0.02" (0.5 mm) + clean cut and scrap bundle sorting + extremely long blade service time
BC 700
BC 700

Strip-brush-trimming

Cost-efficient trimming of staple set and wound roll and disc brushes
+ brush diameter up to 3.3 ft (1 m)
+ brush weight up to 3.300 lbs (1.5 t)
+ standard lengths up to 6.6 ft (2.0 m) (optionally up to 19.0 ft (5.8 m))
+ proven FS 930 trimming technology
+ contour trimming (optional)
+ disc brush trimming (optional)
+ chip extraction and cleaning-friendly design

TwistedBrush machines

A finished brush without trimming afterwards
+ 1 step cylindrical brushes
+ one operation – no later trimming required
+ fill materials abrasive, wire, nylon
+ fast change of fill material
+ freely programmable twisting cycle
+ covered core wire possible
+ fill firmly clamped right into the closed loop
MTI 960
MTI 960
A finished two step brush without trimming afterwards
+ 2 step brushes
+ one operation – no later trimming required
+ fill materials wire, synthetic
+ fast change of fill material
+ freely programmable twisting cycle
+ covered core wire possible
+ fill firmly clamped right into the closed loop
MTI 962
Four core wires and double plane fill
+ 4 core wires
+ high density brushes
+ integrated trimming station direct finishing in diameter on the machine
+ minimal fill material loss
+ material feeding from hank or coil
TIM 4
TIM 4
TIM 4
High density – stub ends
+ high production output
+ all fill materials in hank form
+ minimal material loss
+ no trimming required
+ freely programmable twisting range
ATI 90
ATI 90
ATI 90

Uncategorized

Rational joining of band ends directly in the process
+ useable in line or stand alone
+ integrated band cutter and band grinder

Welding

Winding and welding of spiral packages

Winding and Bending

Roll brushes with up to 8 m length direct in line with strip brush production
+ direct winding in line with your strip brush machine
+ high production speed even at small diameters
Winding and cutting of roll brushes out of endles strip brush
+ special design for easy integration in line with a strip brush machine
+ automatic speed compensation between winding and strip brush machine
+ automatic cutting according to individual number of turns without production stop
WAC 800
Winding of full plastic roll brushes

Wood and furniture industry

Processing of all profile sides in a single run
+ individual configuration
+ Stand alone or integrated in systems
+ 3D surface processing
+ closed operating cell with extraction
+ highest safety for people and materials
B 63
B 63
B 63
Endless natural wood grain effect and individual patterns
+ realistic and natural 3D effect
+ great selection of patterns and structures
+ suitable for all profile types
+ single and double sided processing
+ fast and simple tooling
E12-14
E12-14
E12-14

WPC brushing and embossing

Processing of all profile sides in a single run
+ individual configuration
+ Stand alone or integrated in systems
+ 3D surface processing
+ closed operating cell with extraction
+ highest safety for people and materials
B 63
B 63
B 63
Endless natural wood grain effect and individual patterns
+ realistic and natural 3D effect
+ great selection of patterns and structures
+ suitable for all profile types
+ single and double sided processing
+ fast and simple tooling
E12-14
E12-14
E12-14

CONTACT US

Inquiries

+49 29 53 - 73 300

Aftersales / Spare parts

+49 29 53 - 73 300

Technical support

+49 29 53 - 73 333




    I agree that the information will be collected and processed to answer the request.

    Note: You can revoke your consent at any time for the future by email to [email protected]
    Detailed information in our Privacy Policy

    ABMA Logo
    FEIBP Logo
    VDPB Logo
    EnEff Logo
    VDPB Logo
    TüV ISO 9001 Logo
    Logo Familienfreundliches Unternehmen 2021